Lumen Cloud Connect EVPL to AWS with hosted Direct Connect

Updated by Gavin Lai on Jan 27, 2022
Article Code: kb/1436

In this article:

Overview

The purpose of this document is to provide an end-to-end walk through for a customer setting up Hosted Direct Connect for the first time via Lumen’s Cloud Connect. Information contained is provided to serve as a supplement to AWS documentation linked throughout this document. Users should check the provided links to obtain the most up-to-date information and for more details pertaining to AWS processes. This document is for Cloud Connect services connecting to AWS Direct Connect with a hosted cross connect (see diagram below). The supporting service ordered from Lumen is hosted Cloud Connect to AWS.

aws-direct-connect-options

Audience

Users has ordered Lumen Cloud Connect to connect to their AWS environment.

Prerequisites

Lumen Cloud Connect is ordered and access to AWS Portal with the right permission

What is Direct Connect

Please refer to What is AWS Direct Connect knowledge article.

Lumen Hosted Cloud Connect EVPL to AWS

cloudconnect-evpl-aws-hosted

  • Any NAT configuration that is required due to the use of any AWS Public Services will be the responsibility of the customer.

Lumen Cloud Connect Roles and Responsibilities

Steps required to set up AWS Direct Connect Connectivity End Customer Lumen AWS
Set up connectivity to AWS Direct Connect location
Order Lumen Dedicated Cloud Connect service(s) to AWS Direct Connect X
Decide on the type of VIF required (public or private) X
Create the virtual circuit to AWS X
Monitor the virtual circuit to AWS X
Set up BGP peering between Lumen provided edge and AWS edge device
Configure BGP peering on Lumen PE router facing AWS X
Configure BGP peering on AWS side using console facing Lumen X
Link services on AWS to the dedicated circuit
Accept Hosted Connection via AWS Portal X
Create and link virtual interface, virtual private gateway, VPC, Direct Connect gateway, etc. as applicable using the AWS console X

Overview of procedures to configure Lumen Cloud Connect

  1. Customer requests Lumen Cloud Connect service
  2. Lumen Provisions Cloud Connect to AWS
  3. Accepting the AWS Hosted Connection from the AWS User Console

Procedure to Configure Lumen Cloud Connect

Customer requests Lumen Cloud Connect service

  • To order Lumen Cloud Connect to AWS Direct Connect, contact your Lumen Account Representative
  • Information needed by Lumen to complete the connection:
    • AWS Account ID
    • AWS service(s) you are connecting to
    • Public Virtual Interface (VIF) Requirements
    • VPC / VIF / Direct Connect Gateway Requirements
      • Identify how many VPCs/VIFs etc. you need connectivity to
        • Each VPC/VIF requires a separate logical connection with Dedicated Cloud Connect IPVPN/MPLS from Lumen
    • Determine the amount of bandwidth needed to each VPC/VIF
      • Note: Maximum bandwidth per VPC/VIF is 500 Meg
  • Which AWS Region and/or Direct Connect location do you require connectivity to
  • What contractual term length is desired (1yr, 3yr, 5yr etc.)

Lumen Provisions Cloud Connect to AWS

For latest information, please refer to AWS Direct Connect User Guide

  • Upon network order submission, Lumen will provision a Layer 2 Ethernet virtual private line (EVPL) EVC connection to the requested interconnect point.
  • Lumen completes configuration, and provides you the necessary information to configure the layer-2 turn up on the AWS side using the AWS console:
    • Appropriate VLAN ID for each side of the circuit.
    • Note: Lumen configures VLAN tagging throughout the Lumen network only. You must configure all required IP addressing and BGP routing on your layer-3 device at your location and within the AWS cloud environment using the AWS console. You are also responsible for any/all NAT configurations required for AWS public services.
  • Upon provisioning completion by Lumen, you will receive the configuration information from the Lumen provisioning with instructions as to order completion, activation scheduling, etc. as applicable to your order

Accepting the AWS Hosted Connection from the AWS User Console

Depending on the resiliency options, the process can be different, the detail can be found in AWS Direct Connect User Guide.

  • For instructions on how to accept the AWS Hosted Connection within the AWS Console, please navigate to this link

aws-directconnect-option-hosted

  • If you requested a hosted connection via Lumen Cloud Connect then a hosted connection has been created for you (you cannot create it yourself). You must accept it in the AWS Direct Connect console before you can create a virtual interface.
  • To accept a hosted connection:
    • Open the AWS Direct Connect console at here.
    • If necessary, select the Region in which the hosted connection resides.
    • In the navigation pane, choose "Connections".
    • Select the hosted connection.
    • Select the confirmation check box and choose "Accept Connection".
  • Continue to follow the AWS Direct Connect Getting Started Guide at this same page for instructions on setting up your AWS Direct Connect connection.

Additional AWS Direct Connect and Lumen Cloud Connect Resources

Please refer to the What is AWS Direct Connect Knowledge Article for additional AWS Direct Connect resources.
For further information on Lumen Cloud Connect, please refer to product readiness page

Support